Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car

Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
- 11. Electric equipment
   11.1. Specifications
   11.2. Battery
   + 11.3. System of ignition
   11.4. Coil (i) of ignition
   11.5. Ignition distributor
   11.6. Check and installation of the moment of ignition
   11.7. Block of electronic ignition
   11.8. Induction sensor
   + 11.9. System of a charge of the battery
   + 11:10. Generator
   11:11. System of launch of the engine
   + 11:12. Starter electric motor
   11:13. Traction relay
   11:14. Check of tension
   11:15. Detection of short circuit
   11:16. Check of reliability of grounding
   11:17. Check of integrity of a chain
   11:18. Finding of not closed chain
   11:19. Search of malfunctions
   11:20. Safety locks
   11:21. Fusible crossing points
   11:22. Breakers
   11:23. Relay
   11:24. Breaker of indexes of turn / alarm system
   11:25. Switch of indexes of turn
   11:26. Lock of ignition and drum of the lock
   11:27. Switch of external lighting
   11:28. Screen wiper switch
   11:29. Lamps of headlights
   11:30. Adjustment of headlights
   11:31. Headlight case
   11:32. Replacement of lamps
   11:33. Receiver and loudspeakers
   11:34. Antenna
   + 11:35. Screen wiper electric motor
   11:36. Switch of heating of back glass
   11:37. Heater of back glass
   11:38. Guard of devices
   11:39. Sound signal
   11:40. Electric drive of mirrors
   11:41. Cruise control
   + 11:42. Window regulator electric drive
   11:43. Electric drive of door locks
   11:44. Safety cushions
+ 12. Electrical circuitries

11.5. Ignition distributor

GENERAL INFORMATION

Ignition distributor

1. Cover
2. Runner
3. Cover
4. Distributor case

5. Coil
6. Condenser
7. Induction sensor
8. Dustproof cabin

Removal and installation

PERFORMANCE ORDER

1. Disconnect the battery from weight.
2. Disconnect sockets from the distributor.
3. Find a tag of a conclusion of the 1st cylinder on a cover. If the tag on a cover is absent, then find the corresponding conclusion on a wire from the 1st cylinder.
4. Uncover the distributor, turn the crankshaft and install the runner opposite to a conclusion of the 1st cylinder.
	5. Put a tag on lower the distributor case directly under the index of the runner (it is specified by an arrow).
	6. Designate also position of the case of the distributor on a head of cylinders (it is shown by shooters).
7. If fastening by two bolts with zaplechik for a flange is provided, then release these bolts (to provide a free wheeling of a shaft of the distributor) but completely do not turn off.
8. Turn off a bolt of fastening of the distributor, then give the distributor in the horizontal direction and get it. The turn of the crankshaft after removal of the distributor is not allowed. If the crankshaft nevertheless turned, then install the piston of the 1st cylinder in VMT of a step of compression and orient the runner and the case of the distributor.
	9. Combine selection on a distributor gear wheel with a flute on the case.
	10. Insert the distributor into the engine, having precisely oriented the case on the put tags.
11. If the distributor is not installed in the place, then double-check the tags put before dismantling. Install the distributor precisely on these tags.
12. Wrap a bolt of fastening of the distributor.
13. Further installation is carried out upside-down.
11. Check installation of the moment of ignition (see subsection 11.6), tighten a fastening bolt.