Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car

Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
- 11. Electric equipment
   11.1. Specifications
   11.2. Battery
   + 11.3. System of ignition
   11.4. Coil (i) of ignition
   11.5. Ignition distributor
   11.6. Check and installation of the moment of ignition
   11.7. Block of electronic ignition
   11.8. Induction sensor
   + 11.9. System of a charge of the battery
   + 11:10. Generator
   11:11. System of launch of the engine
   + 11:12. Starter electric motor
   11:13. Traction relay
   11:14. Check of tension
   11:15. Detection of short circuit
   11:16. Check of reliability of grounding
   11:17. Check of integrity of a chain
   11:18. Finding of not closed chain
   11:19. Search of malfunctions
   11:20. Safety locks
   11:21. Fusible crossing points
   11:22. Breakers
   11:23. Relay
   11:24. Breaker of indexes of turn / alarm system
   11:25. Switch of indexes of turn
   11:26. Lock of ignition and drum of the lock
   11:27. Switch of external lighting
   11:28. Screen wiper switch
   11:29. Lamps of headlights
   11:30. Adjustment of headlights
   11:31. Headlight case
   11:32. Replacement of lamps
   11:33. Receiver and loudspeakers
   11:34. Antenna
   + 11:35. Screen wiper electric motor
   11:36. Switch of heating of back glass
   11:37. Heater of back glass
   11:38. Guard of devices
   11:39. Sound signal
   11:40. Electric drive of mirrors
   11:41. Cruise control
   + 11:42. Window regulator electric drive
   11:43. Electric drive of door locks
   11:44. Safety cushions
+ 12. Electrical circuitries

11:37. Heater of back glass

GENERAL INFORMATION

The heater consists from thin a provolok, baked with the surface of glass.

Small destructions a provolok can be repaired independently.

Check

PERFORMANCE ORDER

1. Include ignition and a heater. Between conclusions of a heater connect the voltmeter. If there is no tension, then check a safety lock, the switch and wires.
	2. Dress the put strip of aluminum foil on the voltmeter probe and press down a finger to heater thread in the center.
	3. If tension is equal 6B, thread is serviceable, tension is equal 12B, thread is torn off (the break takes place between the center of thread and weight). If voltage of 0 V, then thread it is torn off between the center and the feeding heater conclusion.
4. If threads are serviceable, then connect (-) - a heater conclusion to weight. If indications of the voltmeter change, then connection with weight unsatisfactory.
	5. The place of break of thread can be established conducting aluminum contact on the voltmeter probe on thread aside from (+) - a conclusion to (-) - to a heater conclusion. At the same time connect the voltmeter with (-) - a conclusion. The indication of the voltmeter has to fall in the place of break sharply.

Repair

PERFORMANCE ORDER

1. It is possible to splice the torn-off heater thread by means of the carrying-out epoxy structure of Dupont N 4817 or equivalent.
2. Disconnect a heater.
3. A steel sponge carefully to a raspoliruyta also wipe the damaged site with alcohol.
4. Impose on the damaged site a mask from an adhesive tape.
5. Prepare pitch, being guided by the instruction.
	6. Apply structure on a crack in a mask, smearing approximately on 18 mm in both parties.
7. 24 hours later unmask.