Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car

Toyota 4ranner
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Specifications
   2.2. Arrangement of knots and units
   + 2.3. Frequency of maintenance and types of scheduled works
   2.4. Intensive service
   + 2.5. Check of level of liquids
   2.6. Check of tires
   2.7. Check of level of liquid in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of steering
   2.9. Replacement of oil in the engine and an oil filter
   2.10. Care of the battery
   2.11. Check of the cooling system
   2.12. Check of a condition of the hoses located in a motor compartment
   2.13. Screen wiper brushes
   2.14. Shift of wheels
   2.15. Check of a suspension bracket of steering
   2.16. Lubricant of a running gear, suspension brackets, steering and details of a body
   2.17. Check of the exhaust system
   2.18. Check of level of oil in the manual transmission
   2.19. Check of level of oil in the transfer case
   2.20. Check of level of oil in a reducer
   2.21. Check of seat belts
   2.22. Check of covers of half shafts
   2.23. Zolotnik of ventilation of a case
   2.24. The filtering element of the air filter
   2.25. Belts of the drive of hinged units
   2.26. Check of fuel system
   2.27. Check of wear of brakes
   2.28. Check and adjustment of pedals of coupling (brake)
   2.29. Replacement of candles
   2.30. Check and adjustment of gaps in valves
   2.31. Replacement of the fuel filter
   2.32. High-voltage wires, runner and cover of the distributor
   2.33. Care of the cooling system
   2.34. Naves and bearings of forward wheels
   2.35. Replacement of liquid in automatic transmission and the filter
   + 2.36. Oil replacement
   2.37. Check of a tank with an absorber
   2.38. Valve check of system of recirculation
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries

2.35. Replacement of liquid in automatic transmission and the filter

GENERAL INFORMATION

Works are performed on the cooled-down engine after recently made trip.

PERFORMANCE ORDER

1. Lift the car and establish on supports.
	2. Substitute the pallet, turn off a drain stopper and merge all liquid, without allowing losses. Put a stopper into place and tighten.
	3. Carefully remove the pallet of a case of transmission and merge the liquid remains. For removal of the pallet turn off bolts and easy blows of the hammer displace, having opened consolidation.
	4. Turn off bolts and remove the filter from the block of valves of transmission (bolts of the filter of transmission are specified by shooters).
5. Check a condition of liquid. If liquid of dark color also exudes a burned smell, then it indicates a transmission overheat. Presence at the pallet or at the filter of small particles of metal or frictional material demonstrates destruction of details internal transmission devices (multidisk coupling). In this case it is recommended to hand over the car in car service.
	6. Wash out the pallet solvent and dry, remove the remains of old consolidation. Install the new filter, having replaced laying (it is specified by an arrow).
	7. Apply the RTV sealant roller on the demountable plane of the pallet, leading round openings from within.
8. Dress a hose on a branch pipe of the index of level and install the pallet. Evenly and gradually tighten bolts till the set moment.
9. Lower the car and through a hose on a branch pipe fill in about 3,5 l of transmission liquid the recommended brand is specified in subsection 2.1.
10. Transfer the selector to situation Park and start the engine.
11. Transfer the selector to all provisions, again transfer to situation Park and check level, if necessary add liquid, having brought level to normal.
12. At the first trips you watch liquid level (on heated-up transmission) and check existence of dribbles from a case.