Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car

Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. 4-cylinder engines
   - 3.2. V6 3,0 engines of l (1993-1994) and 3,4 l (since 1995)
      3.2.1. Specifications
      3.2.2. The types of repair which are carried out without removal of the engine from the car
      3.2.3. Installation of the piston of the 1st cylinder in compression step VMT
      3.2.4. Covers of heads of cylinders
      3.2.5. The soaking-up collector
      3.2.6. Final collectors
      3.2.7. Belt of an asterisk of cam-shafts
      3.2.8. Forward epiploon of the crankshaft
      3.2.9. Epiploons of cam-shafts
      3.2.10. Cam-shafts and pushers
      3.2.11. Heads of cylinders
      3.2.12. Oil pallet
      3.2.13. Oil pump
      3.2.14. Flywheel (drive plate of the hydrotransformer)
      3.2.15. Back epiploon of the crankshaft
      3.2.16. Engine mount details
   + 3.3. Dismantle and capital repairs of the engine
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries

3.2.13. Oil pump

Removal

PERFORMANCE ORDER

1. Remove the pallet.
2. Shoot a gear belt and the lower video of a natyazhitel.
3. Remove the leading asterisk.
4. Remove an oil indicator.
5. Remove the generator.
6. Remove the compressor of the conditioner and take aside.
7. Remove a compressor arm.
8. Disconnect a rod of the regulator of the hydraulic booster and take aside.
9. Shoot the lower video of a natyazhitel.
10. Turn off bolts and remove the pump, having hooked the screw-driver.
	11. Remove a sealant and details of the reducing valve.
	12. Turn out cover screws.
13. Uncover and get gear wheels.
14. Remove the consolidation remains from the demountable planes of the pump, wash out solvent.

Check

PERFORMANCE ORDER

1. Wash out all details in solvent, check existence of wear and damages.
2. Check a condition of details of the reducing valve. At detection of damages replace the piston complete with a spring.
	3. Check the probe a gap between the conducted rotor and the case.
	4. Check the probe a face gap.
	5. Check the probe a gap between rotors (arrow).
6. Compare results to the data specified in subsection 3.2.1.

Installation

PERFORMANCE ORDER

1. Get a crankshaft epiploon, having hooked the screw-driver.
2. Grease and carefully press a new epiploon.
3. Install pump gear wheels in the case by tags up.
4. Put technical vaseline in a pump cavity, lay laying, put a cover and tighten screws.
5. Oil the piston of the reducing valve fresh for the engine and establish valve details.
6. Wash out the condensed surface of the pump.
7. Apply the sealant roller on a pump cover.
8. Install a new sealant in the block of cylinders.
	9. Install the pump, having combined vents of the leading gear wheel with shliyets on the crankshaft.
10. Tighten bolts in a diagonal order with the set moment.
11. Establish other details upside-down, add oil, start the engine. Check oil level repeatedly.