Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car


Toyota 4ranner
- 1. Maintenance instruction
   1.2. Dashboard
   1.3. The combined devices
   1.4. Designation of symbols of light indexes
   1.5. Keys
   1.6. System of an immobilizer (recognition of a code of launch of the engine)
   + 1.7. Doors
   1.8. Cover of the fuel tank
   1.9. Adjustment of a front seat
   1.10. Adjustment of an inclination of a steering wheel
   1.11. Adjustment of provision of a rear-view mirror
   1.12. Plafond of internal lighting
   1.13. Plafond of individual lighting
   1.14. Cleaner and washer of a windshield
   1.15. Cleaner and washer of back glass
   + 1.16. Headlights and indexes of turn
   1.17. Heater of back glass
   1.18. Index of a reserve of fuel
   1.19. The remote thermometer of the cooling means
   1.20. Oil pressure measuring instrument
   1.21. Voltmeter
   1.22. Tachometer
   1.23. Counter of the general run and counter of a daily run
   + 1.24. Indexes and the warning signals
   1.25. Lock of ignition and lock of a steering column
   1.26. Automatic box
   1.27. The AM-UKV radio receiver with electronic control
   1.28. The AM-VHF-radio tape recorder with electronic control
   1.29. Adjustment of the direction of a stream of air
   1.30. Governing bodies of a heater
   1.31. Hours
   1.32. Lighter and ashtray
   1.33. Glove box
   1.34. A container for trifles
   + 1.35. Actions at refusal of launch of the engine
   1.36. Identification numbers of the car
   1.37. Identification number
   1.38. Manufacturer's certificate of origin
   1.39. VECI label
   1.40. Numbers on transmission units
   1.41. Car raising jack
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries


2403db43

1.28. The AM-VHF-radio tape recorder with electronic control
GENERAL INFORMATION

Use of the receiver

PERFORMANCE ORDER
1. Turn on the receiver, having pressed the L.M.U button., choose the stereo mode - or monophonic reception, or press the TI button for reception of the station of broadcasting of road information (see below). On the display L, M symbols, or U will appear. The receiver can also be turned on pressing the PWR.VOL handle.
2. Adjust loudness, turning the PWR.VOL handle.
3. Be adjusted on the necessary station (see Control for the station and Programming of control).
4. At control for the VHF station the receiver will automatically switch in the stereo-reception mode. On the display ST symbol will appear.
5. If the signal weak, then occurs automatic narrowing of a strip of reception for the purpose of decrease in noise.
6. If the signal very weak, then occurs automatic switching of the receiver to the monophonic mode of reception.
7. Adjust a timbre and balance (see Adjustment of a timbre and Adjustment of balance).
8. To switch off the receiver, press the PWR.VOL handle.

Control for the station

PERFORMANCE ORDER
1. Be adjusted on the necessary station by means of one of the ways offered below. On the display value of frequency of control will appear.
Control in the program mode
2. It is used for control for in advance programmed station (see control Programming).
3. Press several times the LMU button until on the display there is no chosen information.
4. Press the button with number which was in advance appropriated to the necessary station. There is a control for the necessary station, and on the display number of the button of the necessary station will appear.
Mode of continuous search
5. In this mode there is an automatic search of the station. After reception of the station control automatically stops.
6. Press at the same time on both parties the TUNE SEEK buttons and wait for a continuous sound signal. The receiver will begin to carry out automatically search of the nearest station with higher or lower frequency of broadcasting.
7. After consistent reception control stops. By each subsequent pressing of the button search will continue before consistent reception of the following station.
8. If because of too weak signal it is not possible to be adjusted after single scanning in all range of frequencies, then search will continue, but at hypersensibility, and on the display the symbol DX will appear.
Manual control
9. Press at the same time on both parties the TUNE SEEK buttons for a while not exceeding 0,5 sec. By each pressing of the button there is a jump to the frequency at which broadcasting is possible.

Control programming

PERFORMANCE ORDER
1. Press several times the LMU button until on the display designation of the chosen range of L, M or U does not appear.
2. You can establish up to six stations in each chosen range (on each pressed button). At installation of the station check those ranges in which the necessary control already is.
3. Be adjusted on the necessary station (see Control for the station).
4. Press one of buttons of the choice of the station and wait for a sound signal. At the same time the station will automatically join when pressing this button which number will appear on the display.
5. To bring control for the new station in memory repeat the procedure described above.
6. Control for the programmed station is erased at power off (a battery detachment, burn-out of a safety lock, etc.).

Obtaining road information from the RDS system (radio data)

PERFORMANCE ORDER
1. The receiver will automatically switch in the mode of reception of the station broadcasting RDS information when switching to VHF range. When switching on the display the name of the relevant radio station and a symbol of RDS will appear.
2. If to be adjusted on the new VHF station broadcasting RDS-information, then on the display there will be a value of frequency, and in 5 sec. the name of the relevant radio station will appear.
3. Control for the necessary station which broadcasts road information is carried out by one of the next ways.
Control by programming, automatic search and manually
4. The order of control is described above.
Control by scanning in all range
5. When on the display there is a symbol of TR (Traffic Program), it means that this station will broadcast road information and data of EON.
6. The receiver is switched to TI range by pressing of the TI button. At the same time on the display the symbol of "TI" will appear.
7. If later 20 sec. after pressing of the TI button the receiver does not find the station, then search of the station on the basis of the list of alternative frequencies (AF list) which comes to an end at detection of the station will begin.
8. The sound signal and a SEARCH symbol on the display warns about transition of the receiver to such mode.
9. If it is not possible to be adjusted on the station after single scanning in all range because of a weak signal, then scanning will repeat, but at hypersensibility what the symbol DX on the display will testify to.
10. If the signal too weak, then the receiver stops search and on the display for 2 seconds NOTHING will appear.
11. If within 20 more seconds the receiver is not adjusted on the station of TI range, then scanning will be started anew.
12. When on the display there is TI, the receiver will accept the TI station only in that case if control is made by search in the automatic mode.
13. If obtaining road information is required, and the station for which the receiver is ready, broadcasts other program, then press the TI button and hold until on the display the symbol does not appear THAT (Traffic Announcement).
14. At emergence of this symbol the receiver ceases to adopt all programs except road or if transfer of road information at the moment is absent, and the cartridge is inserted into a player, then the player which is automatically switched off at the time of the beginning of broadcasting of road information joins.
15. After the end of transfer or if the signal becomes weak, the previous program joins.
16. To come back from the mode of reception of road information to the usual mode press the TI button and hold until from the display the symbol THAT does not disappear.
Control for the tracking mode on networks (NF mode). It is used for search of the RDS station in all strip of frequencies
17. Press the NF button and hold no more than 2 sec., at the same time the receiver will be adjusted on the RDS station, and the adopted program will not be interrupted. On the display NF symbol will appear.
18. At deterioration in conditions of reception control for the station which broadcasts the same program will be made on the basis of the list of the alternative frequencies received from the RDS station.

Adjustment of a timbre

PERFORMANCE ORDER
1. For adjustment of reproduction in to acquire the lower frequencies press several times the MODE button until on the display BASS O does not appear.
2. Then press the level button from any party and establish the necessary timbre. Adjustment range – from BASS-10 to BASS +10, the level of a timbre is displayed on the display.
3. For adjustment of reproduction in to acquire the top frequencies press several times the MODE button until on the display TREB O does not appear.
4. Then press the level button from any party and establish the necessary timbre. Adjustment range – from TREB-10 to TREB +10, the level of a timbre is displayed on the display.

Adjustment of balance

PERFORMANCE ORDER
Two loudspeakers
1. Press several times the MODE button until on the display BAL O does not appear.
2. Then press the level button from any party and establish the necessary balance.
3. Range of adjustment of balance for the left and right loudspeakers - from BAL L14 to BAL R14, the level of balance is displayed on the display.
Four loudspeakers
4. For control of balance between the left and right loudspeaker press several times the MODE button until on the display BAL O does not appear.
5. Then press the level button from any party and establish the necessary balance.
6. Range of adjustment of balance – from BAL L14 to BAL + R14, the level of balance is displayed on the display.
7. For control of balance between forward and back loudspeakers press several times the MODE button until on the display FADE O does not appear.
8. Then press the level button from any party and establish the necessary balance.
9. Range of adjustment of balance of forward and back loudspeakers – from FADE F14 to FADE R14, the level of balance is displayed on the display.