Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car

Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
- 6. Transmissions
   + 6.1. Mechanical transmission
   - 6.2. Automatic transmission
      6.2.1. Specifications
      6.2.2. Diagnostics of transmission
      6.2.3. Gate drive cable
      6.2.4. Draft of transmission
      6.2.5. The blocking switch
      6.2.6. System of fixing of transfers
      6.2.7. Lever of change of transfers
      6.2.8. Removal and installation of transmission
   + 6.3. Transfer case
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries

2403db43 автошампунь для бесконтактной мойки 20л
На сайте курсовая работа синергия.

6.2.8. Removal and installation of transmission


1. Disconnect the battery from weight.
2. Get the probe of the index of level of liquid.
3. Disconnect a cable of a butterfly valve for what weaken adjusting nuts, bring a cable out of an arm and unhook from draft. Disconnect cable latches.
4. Remove average section.
5. On cars 4WD remove the lever of the transfer case for what get a lock ring.
6. Lift the car.
7. Remove the lower guards preventing removal of a box.
8. Merge transmission liquid, install the pallet into place.
9. Turn off bolts of an arm and remove a branch pipe of the index of level of liquid.
10. Disconnect half shafts (see subsection 7.8).
11. Remove a forward exhaust pipe.
12. Turn off a corrugated cap nut and get a speedometer cable. Not to a dopuskeayta of weakening of felt laying and washers.
13. Disconnect from transmission all sockets (the sensor of speed, the solenoid of blocking, the blocking switch, etc.).
14. Disconnect a rod from the lever on transmission.
15. Disconnect from tube transmission, conducting to a cooler.
16. Remove a starter and take wires aside.
17. On cars with the engine 5VZ-FE remove a suspension bracket stabilizer cross-piece.
18. Uncover the hydrotransformer.
19. Designate position of the hydrotransformer on a drive plate, turn off serially 6 bolts for what turn the crankshaft clockwise.
20. Establish a jack under a case (it is desirable the special cart). Turn off bolts of fastening of a shaft of a case to a cross-piece (a photo at the left). Turn off bolts, raise transmission and remove a cross-piece (a photo on the right).
21. Substitute a jack under the engine and turn off bolts of fastening of transmission to the engine.
22. Displace transmission back and remove from the directing pins. Fix the hydrotransformer on transmission.
23. On cars 4WD remove the transfer case.


1. Make sure that the nave of the hydrotransformer is in gearing with the pump.
2. Install transmission on the cart and carefully lift, keeping its horizontal position. Attach liquid cooling tubes.
3. Turn the hydrotransformer and combine the tags put before removal.
4. Carefully give transmission to the engine and establish on the directing pins.
5. Wrap bolts of fastening of transmission and tighten with the set moment.
6. Tighten bolts of fastening of the hydrotransformer.
7. Establish a cross-piece and tighten bolts and nuts.
8. Lower a case shaft, having combined with openings in a cross-piece, tighten bolts and nuts.
9. Further assembly is carried out upside-down (see rice. Automatic transmission (A340 type) of all-wheel drive cars).