Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
+ 3.1. 4-cylinder engines
+ 3.2. V6 3,0 engines of l (1993-1994) and 3,4 l (since 1995)
- 3.3. Dismantle and capital repairs of the engine
3.3.1. Specifications
- 3.3.2. Capital repairs
3.3.2.1. Alternatives
3.3.2.2. Order of dismantling of the engine
3.3.3. Diagnostics of the engine by means of the vacuum gage
3.3.4. Check of a compression in engine cylinders
+ 3.3.5. Dismantle of the power unit
+ 3.3.6. Head of cylinders
3.3.7. Valves
3.3.8. Conrod and piston group
+ 3.3.9. Crankshaft
3.3.10. Block of cylinders
3.3.11. Honningovaniye of cylinders
+ 3.3.12. Rods and pistons
3.3.13. Radical and conrod bearings
3.3.14. Balancer shafts
3.3.15. Assembly order
3.3.16. Piston rings
3.3.17. Launch of the engine after repair and a running in
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electrical circuitries
|
Krivoshipno-shatunny mechanism and piston group of 4-cylinder engines
1. The ring is compression top
2. Disks of an oil scraper ring
3. Flywheel
4. Bolt
5. Rod
6. Connecting rods
7. Rod cover
8. Epiploon
9. Intensifying plate
10. Holder
11. Detonation sensor
12. Perepuskna cooling branch pipe
13. Fuel filter
14. Laying
15. Hose
16. The support is left
17. Radical insert |
18. Cover
19. Persistent ring
20. Crankshaft
21. Asterisk
22, 26. Persistent plate
23. Asterisk
24, 25. Balancer shaft
27. Washer
28. The support is right
29. Drain stopper
30. Oil filter
31, 33. Ring
32. Union
34. Lock ring
35. Finger
36. Broad ring
37. Lower compression ring |
Krivoshipno-shatunny mechanism and piston group of V6 3,0 engines of l
1. Detonation sensor
2. Perepuskna branch pipe of cooling of N1
3. For the car from the manual transmission
4. Flywheel
5. Intensifying plate
6. Epiploon
7. Holder
8. For the car with automatic transmission
9, 11. Remote washer
10. Drive plate
12. Reducing valve
13, 15. Laying
14. Oil cooler
16, 18. Hose
|
17. Union
19. Pressure sensor
20. To tighten a dynamometer key
21. Framework of covers
22, 25. Persistent half rings
23. Radical insert
24. Crankshaft
26. Adjusting bar of the generator
27. Block of cylinders
28. Rod cover
29. Connecting rods
30. Rod
31. Finger
32. Rings
33. Piston
34. Bolt |
Krivoshipno-shatunny mechanism and piston group of V6 3,4 engines of l
1. The ring is compression top
2. The ring is compression lower
3. Disks of an oil scraper ring
4, 18. Lock ring
5. Plug
6. Rod
7. Connecting rods
8. Rod cover
9. Epiploon |
10. Holder
11. Block of cylinders
12. Crankshaft
13, 17. Radical inserts
14. Framework of covers
15, 16. Persistent half rings
19. Finger
20. Piston
21. Dilator of an oil scraper ring |
The following order of full dismantling of the engine is recommended:
– collectors;
– covers of a head of cylinders;
– chain cover, chain, drive details (4-cylinder engines);
– covers of a gear belt a belt, asterisks (on V6 engines);
– head (i) of cylinders;
– pallet;
– oil pump;
– balancer shaft (4-cylinder engines);
– rods and pistons;
– epiploons;
– crankshaft.
|
|
